- Joined
- Feb 6, 2011
- Messages
- 386
- Reaction score
- 190
This is a simple tutorial to get your vbox live to the net so people outside your network can play on your server
This is more directed towards Ronny1982 VBOX PWServer on hrace009 page http://forum.ragezone.com/f452/vbox-image-pw-1-3-a-650130/
i see alot of posts about getting that live so here is a tutorial
MAKE SURE NO OTHER SYSTEM IS USING THAT IP
HAVE YOUR SERVER OFF AT THIS POINT
\\\STEP 1\\\
Put your Vbox into Bridge Mode
Select the PWServer-hrace009 system
go to Settings (gold Gear) on the start up area
Go to Network
if not already activate check "Enable Network Adapter"
Attached to "Bridged Adapter"
Name "Select the device your getting internet from"
Click the Advanced arrow
Adapter Type: "PCnet-FAST III (Am79C973)"
Mac Address: "080027AD81AD"
and make sure you have enabled "Cable Connected"
!!!!!!!!!!!!For Latest Version of VBox!!!!!!!!!!!!!!!!!!!!
there is word that you can also use NAT and enable the port forwarding that way.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
\\\STEP 2\\\
in your VBOX type in terminal ifconfig
Link encap:Ethernet HWaddr 08:00:27:ad:81:ad
inet addr:192.168.0.10 the rest after this doesnt matter
its the ip and the mac address you need
Now as it is a Bridged Server you need to open the ports on your firewall.
Alot of people get confused thinking its just the servers IP or the computer's IP, YOU HAVE TO PUT BOTH
example
Vbox server is 192.168.0.10
Computer running Vbox is 192.168.0.30
and add these ports 80 8080 29000 to both 192.168.0.10 AND 192.168.0.30
YOU MUST HAVE BOTH IP's registered with those ports
add those to your firewall as well
go to your Router
there is 2 ways of doing this.
DMZ your computer example 192.168.0.30 and enable the DMZ
Now Port Forward your server in your Port Forward area
if your server is not running 192.168.0.10 use the ip it provides
can sometimes be 192.168.0.51 but as i said this is for ronny1982 / hrace009 page and the ip is set to 192.168.0.10
TCP 29000 192.168.0.10 enable it
TCP 8080 192.168.0.10 enable it
TCP 80 192.168.0.10 enable it
Should work
OR you can if your router will allow you too is multiple forwards and you wont have to use DMZ
TCP 29000 192.168.0.30 enable it
TCP 8080 192.168.0.30 enable it
TCP 80 192.168.0.30 enable it
TCP 29000 192.168.0.10 enable it
TCP 8080 192.168.0.10 enable it
TCP 80 192.168.0.10 enable it
hope this makes sence to everyone i was playing around and found out how to work the VBox
IF YOUR RUNNING AN SMC ROUTER THERE IS A LITTLE MORE CHALLENGE TO GET PORT FORWARDING TO WORK
if I have missed anything let me know
ANOTHER THING... if your using canyouseeme.org to see if the ports are open, they will not show until you start the server from 192.168.0.10:8080/pwAdmin then it will become live to the net
\\\PROBLEM WITH IP, YOU CAN CHANGE IT\\\
This is more directed towards Ronny1982 VBOX PWServer on hrace009 page http://forum.ragezone.com/f452/vbox-image-pw-1-3-a-650130/
i see alot of posts about getting that live so here is a tutorial
MAKE SURE NO OTHER SYSTEM IS USING THAT IP
HAVE YOUR SERVER OFF AT THIS POINT
\\\STEP 1\\\
Put your Vbox into Bridge Mode
Select the PWServer-hrace009 system
go to Settings (gold Gear) on the start up area
Go to Network
if not already activate check "Enable Network Adapter"
Attached to "Bridged Adapter"
Name "Select the device your getting internet from"
Click the Advanced arrow
Adapter Type: "PCnet-FAST III (Am79C973)"
Mac Address: "080027AD81AD"
and make sure you have enabled "Cable Connected"
!!!!!!!!!!!!For Latest Version of VBox!!!!!!!!!!!!!!!!!!!!
there is word that you can also use NAT and enable the port forwarding that way.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
\\\STEP 2\\\
in your VBOX type in terminal ifconfig
Link encap:Ethernet HWaddr 08:00:27:ad:81:ad
inet addr:192.168.0.10 the rest after this doesnt matter
its the ip and the mac address you need
Now as it is a Bridged Server you need to open the ports on your firewall.
Alot of people get confused thinking its just the servers IP or the computer's IP, YOU HAVE TO PUT BOTH
example
Vbox server is 192.168.0.10
Computer running Vbox is 192.168.0.30
and add these ports 80 8080 29000 to both 192.168.0.10 AND 192.168.0.30
YOU MUST HAVE BOTH IP's registered with those ports
add those to your firewall as well
go to your Router
You must be registered to see links
enter your username and passwordthere is 2 ways of doing this.
DMZ your computer example 192.168.0.30 and enable the DMZ
Now Port Forward your server in your Port Forward area
if your server is not running 192.168.0.10 use the ip it provides
can sometimes be 192.168.0.51 but as i said this is for ronny1982 / hrace009 page and the ip is set to 192.168.0.10
TCP 29000 192.168.0.10 enable it
TCP 8080 192.168.0.10 enable it
TCP 80 192.168.0.10 enable it
Should work
OR you can if your router will allow you too is multiple forwards and you wont have to use DMZ
TCP 29000 192.168.0.30 enable it
TCP 8080 192.168.0.30 enable it
TCP 80 192.168.0.30 enable it
TCP 29000 192.168.0.10 enable it
TCP 8080 192.168.0.10 enable it
TCP 80 192.168.0.10 enable it
hope this makes sence to everyone i was playing around and found out how to work the VBox
IF YOUR RUNNING AN SMC ROUTER THERE IS A LITTLE MORE CHALLENGE TO GET PORT FORWARDING TO WORK
if I have missed anything let me know
ANOTHER THING... if your using canyouseeme.org to see if the ports are open, they will not show until you start the server from 192.168.0.10:8080/pwAdmin then it will become live to the net
\\\PROBLEM WITH IP, YOU CAN CHANGE IT\\\
change your VBOX Network Interface /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
iface eth0 inet static
address YOUR VBOX IP
netmask YOUR NETMASK
network 172.16.0.0 <<< Always Fill This XXX.XXX.0.0
broadcast YOUR NEWORK BRODCAST
gateway YOUR GATEWAY IP TO INTERNET
# dns-* options are implemented by the resolvconf package, if installed
dns-nameservers YOUR DOMAIN IP, IF YOU USE DOMAIN
dns-search YOUR DOMAIN NAME, IF YOU USE DOMAIN
-----------------------------------------------------------------
and don't forget to Replace the IPs with your current addresses except the lines with 0.0.0.0
/PWServer/gacd/gamesys.conf
/PWServer/gamed/gmserver.conf
/PWServer/gamed/gs.conf
/PWServer/gamed/gsrollback.conf
/PWServer/gamedbd/cashstat.conf
/PWServer/gamedbd/gamesys.conf
/PWServer/gdeliveryd/gamesys.conf
/PWServer/gfactiond/gamesys.conf
/PWServer/glinkd/gamesys.conf
/PWServer/logservice/logservice.conf
/PWServer/uniquenamed/gamesys.conf
/etc/authd.conf
/etc/gmopgen.xml
/etc/GMserver.conf
/etc/hosts
/etc/iweb.conf
Last edited: